Questions tagged [intake]
10 questions
1
vote
0 answers
How to interpret "crankshaft adaptation inlet Grad KW" value?
I'm trying to understand the meaning of this value and the implications of it being over the 120 limit.
Do you think you could help me out with some thoughts about it?
I think it should say "camshaft" instead of "crankshaft", since that is the…
learner
- 11
- 2
1
vote
0 answers
The HG fell from 22 to 18 after 'addressing' post-supercharger intake leaks
I have an ODB 1 supercharged 540I/6 (E34 1995 if that matters) that was hitting 10 PSI of boost relatively easy last summer. The car has been sitting for a while, and the boost was barely touching 5 PSI when I drove it last week. The vacuum gauge at…
Aleksey Korzun
- 111
- 2
1
vote
0 answers
02 Civic SiR "faint whistling" sound under load
I'm getting what I can best describe as a "faint whistling" sound, mostly under load, sometimes faintly when revving in neutral. I'd liken it to someone blowing a referee's whistle way off in the distance.
I just got this car, so I've done a bit of…
autobottodoggo
- 673
- 2
- 11
- 19
1
vote
2 answers
Clear oily fluid collects in intake silencer baffle
While looking for vacuum leaks to explain a P0171 code, I noticed a sloshing noise/feel when I removed the intake silencer baffle (which is part of the intake tubing that sits between the MAF sensor, and the intake throttle body.)
When I poured this…
Cognitive Hazard
- 874
- 1
- 10
- 24
0
votes
0 answers
I have a 2014 qx60, ive replaced all plugs and one bad coil and air filter but i still have rough idle and no drivablilty because the engine shutters
I have replaced all plugs and the bad coil and cleaned the mass airflow sensor, why does it still sound like a Subaru at idle and shake and jitter while driving with traffic unless using the manual tap shift? I need help bad.
0
votes
1 answer
A MAP sensor small piece of plastic and a nipple fell into intake
I tried to remove the MAP sensor (the car is Clio 3 1.6 16v k4m engine) and it was moving very easily and just tried a little bit to pull it out and a small piece of plastic with an oring was just fallen out in the intake...
Welzix Awnie
- 1
- 1
0
votes
1 answer
Do carburetors protect intake valves from carbon deposits?
For a long time, most car engines were using multi-point port injection that sprays fuel directly at the intake valves. Today, engines are increasingly commonly direct injected. A problem of direct injection engines is that the intake valves often…
juhist
- 15,535
- 13
- 62
- 104
0
votes
0 answers
Mercedes P2004 error code
I have 2007 Mercedes s550, It runs without any issues but I can see P2004 error code which says: Intake Manifold Runner control stuck open Bank 1a.
A week ago I saw a check engine light on, I plugged in ODB2 device and was able to read P2004 and…
Rainmaker
- 101
- 1
0
votes
0 answers
2003 cts cadillac 3.2
2 cts cadillac. On the top of the air intake manifold runs a black strip. Underneath that black strip my gasket or O ring has broke. I don't know the name of it and have gone to several automotive stores and they don't either. Can anyone please help…
-1
votes
2 answers
Can I Relocate The PCV Air Invlet Line from the Air Tube into the Air Box?
If I relocate the PCV valve line into the air box housing, will I gain engine performance and efficiency?
