Lenovo ThinkPad X1 Carbon 6th Gen Fan Replacement

Written By: Michael Megna

Comments: 9

Lenovo ThinkPad X1 Carbon 6th Gen Fan Replacement

Difficulty

Moderate

Steps

Time Required

10 - 20 minutes

Introduction

This guide will cover how to remove and replace the fan in the Lenovo ThinkPad X1 Carbon 6th Gen. This may be necessary if you need to access the fan for cleaning, or if you need to replace a broken or faulty fan. It is important for your fan to work properly because it prevents overheating which may damage your laptop. If you are having trouble with your computer fan, consult our troubleshooting page. Before beginning, be sure to power off your laptop and disconnect it from any power source.

Tools

Parts

Step 1

Use a Phillips #0 screwdriver to unscrew the five screws that secure the back cover to the laptop.
The screws do not completely come off from the back cover. Loosen until the screws are completely loose.

Step 2

Use a Jimmy to lift the cover directly up off of the locating pins.
Though a metal opening tool is shown in the image, we recommend using plastic opening tools to minimize any cosmetic damage.
Remove the back cover.
If you encounter resistance when lifting the cover, revisit the screws to see if any of them are still threaded on to the device.

I thank you for these instructions. They were quite helpful and I successfully replaced the fan. There is one thing however. Your instructions stated the following: "Be sure to pull on all of the cables at the same time."

I disagree. One should never pull the wires. I was able to nudge the one part of the connector loose from the other part that it fit into." I then put the new fan in and gently and carefully pushed the connecting parts together.

Otherwise, your instructions were clear and to the point. Thank you very much

ALAN L SILBERLIGHT -

The image shows prying the cover open at the bottom right. In fact, there are tabs securing the bottom edge to the frame. The cover needs to be pried open at the top edge. Once the top edge is released, the cover can be shifted slightly toward the top of the image to disengage the tabs at the bottom.

This error, along with the similar error about removing the battery in step 4, suggests that the instructions were written with the laptop in the opposite orientation than what is shown in the images.

EatCroc3 -

I also don't believe that the iFixit Jimmy is necessary - in fact, it might scratch up the exterior paint of the X1 Carbon Gen 6. Instead, I find the triangular iFixit picks are more appropriate for the task: iFixit Opening Picks (Set of 6)

Also, at least for my unit, the lid comes off easily and I only use the plastic picks if there's any resistance and I don't want to risk breaking any of the clips.

Tai Lam -

Step 3

Use a Phillips #0 screwdriver to loosen the four screws that secure the fan to the motherboard.
The screws do not completely come off from the fan mount. Loosen until the screws are completely loose.

Step 4

Use nylon tipped tweezers, or your fingers, to gently pull the fan's power cable towards the SSD, disconnecting it from the pins.
Be sure to pull on all of the cables at the same time.

Step 5

Use a plastic opening pick to lift the fan mount.
Use your fingers to gently pull the fan diagonally away from where it is connected.

Step 6

Turn the fan over to expose the interior.
If necessary, clean out the fan or wipe away and replace the thermal paste.

All good. But most of us occasional Fixit-ers don't happen to have thermal paste lying around. Would have been helpful to include it in your list of necessary parts and tools. Otherwise, instructions were clear as crystal and worked as advertised. Tx!

ESR Westchester -

Great call out! I updated this guide to include the Thermal Paste as a required component. Thank you!!

Matt Zieminski -

I'm about to do this repair, and I'm planning to use Honeywell PTM7950 SP rather than thermal paste. It occurred to me that maybe I should ask the experts if this is a good idea. PTM7950 has rave reviews on heat conductivity, and it appears that it will fit fine under the fan. But am I missing a problem that will come back to haunt me someday?

BiggerHammer -

It's probably fine to use Honeywell PTM7950, just make sure to perform a CPU-intensive tasks (such as synthetic benchmarking) so that any pockets of air can escape after initial post-market application. If it doesn't perform as intended, then you can always remove it and use a more conventional thermal paste on the CPU.

Tai Lam -

There is one detail that many videos/guides almost never explicitly mention: you don't put any thermal paste on the smaller "die" for the X1 Carbon Gen 6 - and you only catch this if you see others cleaning the original thermal paste for the first time.

* This is mentioned in the description of a video from Duraputer in February 2024: https://youtu.be/VLb8vIzdi6s

* This is also mentioned in a pinned comment of a video from Salem Techsperts in October 2022: https://www.youtube.com/watch?v=TAIypDVt...

Tai Lam - 31/03/25

Thank you. Mine just died

nitsudg13 -