Harman Kardon Onyx Studio 2 Circuit Board Replacement

Written By: Alexandra Achtenberg
  • Comments: 18
Harman Kardon Onyx Studio 2 Circuit Board Replacement

Difficulty

Moderate

Steps

9

Time Required

15 - 25 minutes

Introduction

If you have looked at the troubleshooting page and identified that your issues with your Onyx Studio 2 are indeed due to the circuit board being bad, this guide will walk you through how to replace it.

  1. dBMtxPy1K1rUnFpu
    dBMtxPy1K1rUnFpu
    iQOTA3V6DRt2d21M
    dQ2kJq1EW24lJYMB

    • Using a plastic opening tool, pry off the front grill by wedging it in the notch on the front of the device.

    Where can I find a new front panel for my speaker

    consomme69 -

    If I take this off can I put it back on

    Burger King -

  2. o5SWK6TwGvJXXZkQ
    o5SWK6TwGvJXXZkQ
    jqcCAC2kkM2JaaRl

    • Remove the five 14.4 mm T10 Torx screws.

    There are NO torxscrews. You have to pull out the rubber grille grips that are inside the screw holes FIRST, then use a regular sized Phillips head screwdriver to remove the cover. No Torxscrewdiver needed. I found this out after I had already purchased one from you guys.

    phillip columbus -

    Mi bocina no tiene los 5 tornillos a la vista,tiene las cavidades ciegas, como lo abro???

    Eduardo Heine -

    Yes there are no Torx screws… you have to remove the rubber grips them the Philip Screws..

    Joe Lim -

  3. aLaClpNCSQVOuCfs

    • Gently pull the front apart from the back.

  4. 1SWuvDl2qU1UaEUc
    1SWuvDl2qU1UaEUc
    yCr1XiiAOCKacJsD

    • Remove the four wires connecting the front and back panels.

    • Pinch the connector tab and pull gently upwards.

    • Repeat for the other three connectors.

    Please can I get a replacement of my panel to the phone

    Chinedu Ogunedo -

  5. MxWnQFehXaDmTplm

    • Pull the silicone button band off of the outer edge of the speaker.

  6. LPmilUqrJAlOHlTy
    LPmilUqrJAlOHlTy
    i3vgKRRIW6feDDuw

    • Disconnect the two pressure connections from the circuit board.

  7. ZEkMh32Usjwbdy5U
    ZEkMh32Usjwbdy5U
    nusK3sFgWBOTkjkG

    • Gently remove the control board band by placing fingers in contact with it through the button openings.

    • Work from the outer edges in so as not to bend the band.

    From where to buy Control panel

    ali -

    From where to buy this control panel

    ali -

    My speakers control board band broke. If possible, where can I find replacement?

    Abraham Lepez -

  8. mYOLRBFQcPCPT1oE
    mYOLRBFQcPCPT1oE
    gT4EIp3YMS2Q1Bi1

    • Disconnect the remaining connectors from the circuit board.

    • Disconnect the Bluetooth antenna.

  9. 6KYrct1kDkhK5dWw
    6KYrct1kDkhK5dWw
    QcCIKnfkO4dULMNm

    • Remove the four 10 mm T10 Torx screws.

    • Pull the circuit board out of the device as it is now free.

    Bisa di kirim

    Mala Ganni -

    Bisa pesan 1

    Mala Ganni -

    I own two of these and the both shut down on their own.. where do I buy the replacement boards from?

    Darren Vincent -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Alexandra Achtenberg

Member since: 02/02/17

2096 Reputation

6 comments

Where do I get another one

Adrian tlahuel -

Where we buy the board?

Eric Therrien -

Umm… this was rather anticlimactic. Last step was basically like “and now contemplate your life choices”.

markcendan -

Where can I Buy a new hk onix studio Main board?

tecnologia en localizaciòn -

My speaker was working great. I just disconnected my phone to make a call, put YouTube back on it was all mumbled & the big button in the back kept pulsing so fast.

Maureen Field -

Donde consigo una placa nueva?

Marcelo Peña -