Framework Laptop 12 Fan Removal

Written By: Arthur Shi
  • Comments: 0
Framework Laptop 12 Fan Removal

Difficulty

Moderate

Steps

13

Time Required

5 - 15 minutes

Introduction

Fan removal prereq guide

  1. ENj2nRYJffBN2QaN
    ENj2nRYJffBN2QaN
    YjlDgdAsDVIlgqUJ
    GRNSY6XxqDVbUVQJ

    • Before you begin repairs, unplug your laptop and shut it down from the operating system. This ensures that the laptop isn't in standby/suspend mode.

    • The indicator LEDs along the edges should be unlit. The laptop should be silent.

    • If you accidentally turn on the laptop during repair, hold the power button down for 10 seconds to shut it down.

    • Make sure your Framework Screwdriver has the T5 Torx bit (labeled as T-5) facing outwards. If it's not, pull the bit out and flip it.

  2. ubIRwnfForMuSctD

    • Set your Framework Laptop face-down on a clean work surface.

  3. uSiaYQJxHWQEtBTp
    uSiaYQJxHWQEtBTp
    4PYD5BWmLBijnqFr

    • Use your Framework Screwdriver to fully loosen the eight captive T5 Torx screws on the bottom of your laptop.

    • Most screws in your Framework Laptop (including these) are captive—they're designed to stay in place after you loosen them.

    • Your laptop comes with a spare set of screws in the frame above the battery. Be careful—the replacement screws aren't captive.

  4. UomOMxHFjJlXOmVI

    • Flip your laptop over so it's face-up on your work surface.

  5. BAlEsafUboQ4NySF
    BAlEsafUboQ4NySF
    IOc5J3IPRwcuJcrW

    • Open the laptop lid so that both the screen and the base lie flat on your work surface.

  6. 1rUg25vLV4eVwDT1
    1rUg25vLV4eVwDT1
    PI4YlkgvqAGikOsI
    P4UYnHUqKXiVjnPu

    • Use your fingers to grip the Input Cover in the hinge cutouts.

    • Lift upwards to swing the Input Cover up from the base of the laptop.

    • There are magnets holding the Input Cover down, so you'll feel some resistance. If it feels like a lot of force is required, check that you've fully loosened all the screws on the bottom of your laptop.

    • Remove the Input Cover.

  7. b5AQM3feYGn4ttQZ

    • Use your Framework Screwdriver to loosen the six captive T5 Torx screws securing the battery.

  8. QMPLTpItI3EVDGEI
    QMPLTpItI3EVDGEI
    qXL3hfIHcHhpCpPg

    • Grab the orange battery tab with your fingers and lift straight up to disconnect the battery.

    • The battery connector can be tight, requiring some force. If it feels like part of the battery won't come up, check that the battery screws are fully loosened.

  9. vBhTTUMPMdexvY2I
    vBhTTUMPMdexvY2I
    BpR3xLIgaPNfTJcs

    • Lift and remove the battery from the laptop.

  10. PSHXb6UOtMs1DU3m
    PSHXb6UOtMs1DU3m
    Hww1WveUsYaVXQKi
    c4IAJkc5w4r2DR4y

    • Use the flat end of your Framework Screwdriver to gently push on one of the fan connector's protruding edges, then the other, to loosen the connector out of its socket.

  11. lB2dosTkuvOOvGXc
    lB2dosTkuvOOvGXc
    ThsWyKVZFcIisn11

    • Use your fingers and your Framework Screwdriver to slide the fan connector out of its socket.

  12. mKJyC4J46PFXybtg

    • Use your Framework Screwdriver to loosen the two captive T5 Torx screws securing the fan.

  13. IBZPBj34FC2cpsLX
    IBZPBj34FC2cpsLX
    EXnBhVYTCroX4ngJ

    • Lift and remove the fan.

Author

Arthur Shi

Member since: 03/01/18

296850 Reputation

0 comments